Chromalox 1603 User Manual

1601E1601E1601E1601E1601E 4 digit single display temperature controller1603E1603E1603E1603E1603E Dual 3 digit display temperature controllerIssue date

4GBGBGBGBGBline cables.5) OUT 3 and logic input are mutually exclusive.The follow these recommendations to avoid seriousproblems which may occur when

5GBGBGBGBGBVOLTAGE OUTS FOR SSR DRIVEVOLTAGE OUTS FOR SSR DRIVEVOLTAGE OUTS FOR SSR DRIVEVOLTAGE OUTS FOR SSR DRIVEVOLTAGE OUTS FOR SSR DRIVEFig. 7

6GBGBGBGBGB4.4.4.4.4.CONFIGURATIONCONFIGURATIONCONFIGURATIONCONFIGURATIONCONFIGURATION4.14.14.14.14.1PUSHBUTTON FUNCTIONPUSHBUTTON FUNCTIONPUSHBUTTON

7GBGBGBGBGBcode and the numerical value alternatively.To alter the value set press  or  and confirmwith FUNC.The parameter for loading the default p

8GBGBGBGBGBP5 = Function of Out 2P5 = Function of Out 2P5 = Function of Out 2P5 = Function of Out 2P5 = Function of Out 20 = Not used or used as event

9GBGBGBGBGBP10P10P10P10P10=====Threshold of the “Soft Start”Threshold of the “Soft Start”Threshold of the “Soft Start”Threshold of the “Soft Start”Thr

10GBGBGBGBGBP15P15P15P15P15-----SMART function enabling/SMART function enabling/SMART function enabling/SMART function enabling/SMART function enablin

11GBGBGBGBGBP19P19P19P19P19=====Automatic calculation of "relativeAutomatic calculation of "relativeAutomatic calculation of "relativeA

12GBGBGBGBGBWhen the time count is equal to 0 the instrumentcomes back to the SP set point and the output 2will be reset.For other details see paragra

13GBGBGBGBGBThe Out 2 reset will be made when the logic inputwill be closed.For other details see paragraph "5.7 Timer"5.7 Timer"5.7 Ti

A. 21601-03-A-CX.pmd 02/12/2003, 15.592

14GBGBGBGBGBNOTENOTENOTENOTENOTE: The alarm stand-by function disables thealarm indication at instrument start up and after aset point modification un

15GBGBGBGBGB3) Press the FUNC pushbutton to save the newvalue and go to the next parameter.4) Press SMT to return to the previous parameterwithout sav

16GBGBGBGBGB3) The limits of the proportional band settable bythe SMART function are programmed byparameters P16, P17 and P18 .4) The lower limit of t

17GBGBGBGBGBIf the out is turned OFF when the SMARTfunction was performing the second part of theSMT algorithm (LED SMT lit), the SMARTfunction will b

18GBGBGBGBGB5.105.105.105.105.10OPERATIVE PARAMETERSOPERATIVE PARAMETERSOPERATIVE PARAMETERSOPERATIVE PARAMETERSOPERATIVE PARAMETERSThe following is a

19GBGBGBGBGBspan or 1 LSD.NoteNoteNoteNoteNote: If the hysteresis of a band alarm islarger than the alarm band, theinstrument will use an hysteresis v

20GBGBGBGBGBSpan: from 1 to 200 s.rCrCrCrCrC Relative Cooling gain.This is skipped if Pb = 0 (ON/OFF action)or P5 is not 5.Span: from 0.20 to 1.00OLPO

21GBGBGBGBGBTimer mode 2 [P22 = 6]Timer mode 2 [P22 = 6]Timer mode 2 [P22 = 6]Timer mode 2 [P22 = 6]Timer mode 2 [P22 = 6]When the contact is closed,

22GBGBGBGBGBTimer mode 4 [P22= 8]Timer mode 4 [P22= 8]Timer mode 4 [P22= 8]Timer mode 4 [P22= 8]Timer mode 4 [P22= 8]The instrument operates using SP

23GBGBGBGBGBTimer mode 6 [P22 = 10]Timer mode 6 [P22 = 10]Timer mode 6 [P22 = 10]Timer mode 6 [P22 = 10]Timer mode 6 [P22 = 10]The instrument starts i

A. 3INDEXINDEXINDEXINDEXINDEXA.A.A.A.A.ORDER TABLEORDER TABLEORDER TABLEORDER TABLEORDER TABLE...

24GBGBGBGBGB5.13 “Soft Start” FUNCTION5.13 “Soft Start” FUNCTION5.13 “Soft Start” FUNCTION5.13 “Soft Start” FUNCTION5.13 “Soft Start” FUNCTIONAt

25GBGBGBGBGB- The instrument is set to use two control outs andan UNDERRANGE is detected, OUT 1 turns ONand OUT 2 turns OFF.For inputs from thermocoup

26GBGBGBGBGB7.7.7.7.7.TECHNICALTECHNICALTECHNICALTECHNICALTECHNICALCHARACTERISTICSCHARACTERISTICSCHARACTERISTICSCHARACTERISTICSCHARACTERISTICS7.17.17.

27GBGBGBGBGBMeasuring spanMeasuring spanMeasuring spanMeasuring spanMeasuring spanIn brackets the data of model1601ERTDRTDRTDRTDRTDtypetypetypetypetyp

28GBGBGBGBGB7.47.47.47.47.4OUTSOUTSOUTSOUTSOUTSOUT 1 (Heating):OUT 1 (Heating):OUT 1 (Heating):OUT 1 (Heating):OUT 1 (Heating):Relay out with SPDT con

B. 1B.B.B.B.B.DEFAULT PARAMETERSDEFAULT PARAMETERSDEFAULT PARAMETERSDEFAULT PARAMETERSDEFAULT PARAMETERSDEFAULT OPERATIVE PARAM-DEFAULT OPERATIVE PARA

B. 2DEFAULT CONFIGURATIONDEFAULT CONFIGURATIONDEFAULT CONFIGURATIONDEFAULT CONFIGURATIONDEFAULT CONFIGURATIONPARAMETERSPARAMETERSPARAMETERSPARAMETERSP

B. 3The following is a list of the default parameters loaded during the above procedure: PRODUCT1601E1601E1601E1601E1601E1603E1603E1603E1603E1603E

Warranty And Limitation Of Remedy And ReliabilityWarranty And Limitation Of Remedy And ReliabilityWarranty And Limitation Of Remedy And ReliabilityWar

Model identificationModel identificationModel identificationModel identificationModel identificationModelModelModelModelModel1601E 4 digit single dis

170.IU0.16X.E01ChrChrChrChrChromaloxomaloxomaloxomaloxomalox®1382 HEIL QUAKER BOULEVARDLAVERGNE, TN 37086-3536PHONE (615) 793-3900FAX (615) 793-3563TO

A. 5A.A.A.A.A.OUTLINE AND CUT OUT DIMENSIONSOUTLINE AND CUT OUT DIMENSIONSOUTLINE AND CUT OUT DIMENSIONSOUTLINE AND CUT OUT DIMENSIONSOUTLINE AND CUT

A. 61601-03-A-CX.pmd 02/12/2003, 15.596

1GBGBGBGBGB1.1.1.1.1.MOUNTINGMOUNTINGMOUNTINGMOUNTINGMOUNTINGSelect a mounting location where there isminimum vibration and the ambient temperatureran

2GBGBGBGBGBMEASURING INPUTSMEASURING INPUTSMEASURING INPUTSMEASURING INPUTSMEASURING INPUTSSAFETY NOTESAFETY NOTESAFETY NOTESAFETY NOTESAFETY NOTE: An

3GBGBGBGBGBRTD INPUTRTD INPUTRTD INPUTRTD INPUTRTD INPUTFig. 4 RTD CONNECTIONSAFETY NOTESSAFETY NOTESSAFETY NOTESSAFETY NOTESSAFETY NOTES:1) Do not ru