25
GBGB
GBGB
GB
- The instrument is set to use two control outs and
an UNDERRANGE is detected, OUT 1 turns ON
and OUT 2 turns OFF.
For inputs from thermocouple the underrange
indication can be selected as shown in section 7.2
of this manual.
NOTE:NOTE:
NOTE:NOTE:
NOTE: When an
overrange
or an
underrange
is
detected, the alarms operate as if the
instrument had detected the maximum or
the minimum measurable value
respectively.
To eliminate the out of span condition, proceed as
follows:
1) Check the input signal source and the
connecting line.
2) Make sure that the input signal is in
accordance with the instrument configuration.
Otherwise, modify the input configuration (see
section 4).
3) If no error is detected, send the instrument to
your supplier to be checked.
6.26.2
6.26.2
6.2
ERROR MESSAGESERROR MESSAGES
ERROR MESSAGESERROR MESSAGES
ERROR MESSAGES
Diagnostics are made on switching on and during
normal operation.
If the instrument detects an error condition the
display will show:
1603E:
“
ErrErr
ErrErr
Err” in the lower display and the code
which identifies the type of error in the
upper display.
1601E:
“
EE
EE
E” and the error code.
The complete list of all the possible errors follows
in numerical order.
Some errors automatically reset the instrument: if
the error persists, send the instrument to your
supplier to be checked.
6.36.3
6.36.3
6.3
LIST OF POSSIBLE ERRORSLIST OF POSSIBLE ERRORS
LIST OF POSSIBLE ERRORSLIST OF POSSIBLE ERRORS
LIST OF POSSIBLE ERRORS
100100
100100
100 EEPROM writing error.
Consult your supplier.
150150
150150
150 Generic CPU error.
Consult your supplier.
2xx2xx
2xx2xx
2xx Error in the configuration parameters.
The two less significant figures indicate
the number of the incorrect parameter
(e.g.
209 Err209 Err
209 Err209 Err
209 Err indicates error of
parameter P9).
Press SMT and FUNC, then set the
parameter correctly.
See section 4.
301301
301301
301 RTD input calibration error.
Contact your supplier.
305305
305305
305 TC input calibration error.
Contact your supplier.
307307
307307
307 RJ input calibration error.
Contact your supplier.
400400
400400
400
Error in the operator parameters.Error in the operator parameters.
Error in the operator parameters.Error in the operator parameters.
Error in the operator parameters.
To deal with the problem, enterTo deal with the problem, enter
To deal with the problem, enterTo deal with the problem, enter
To deal with the problem, enter
the predefined parametersthe predefined parameters
the predefined parametersthe predefined parameters
the predefined parameters
(“Default Parameters”, see(“Default Parameters”, see
(“Default Parameters”, see(“Default Parameters”, see
(“Default Parameters”, see
section B), pressing pushbuttonssection B), pressing pushbuttons
section B), pressing pushbuttonssection B), pressing pushbuttons
section B), pressing pushbuttons
and and
and and
and
at the same time. at the same time.
at the same time. at the same time.
at the same time.
Then set the operatorThen set the operator
Then set the operatorThen set the operator
Then set the operator
parameters.parameters.
parameters.parameters.
parameters.
This will not reset theThis will not reset the
This will not reset theThis will not reset the
This will not reset the
configuration parameters.configuration parameters.
configuration parameters.configuration parameters.
configuration parameters.
500500
500500
500 Auto-zero error
Contact your supplier.
502502
502502
502 RJ error
Contact your supplier.
510510
510510
510 Error during calibration.
Contact your supplier.
1601-03-1-CX.pmd 13/01/2004, 10.4325
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals